Set Table Bench
Set Table Bench
Build A Work Bench
Here are the plans to make a workbench for your shop. Fairly easy to build, these plans make a nice, solid, compact bench to fit in nearly any workshop.
Items needed:
Top 198 x 48 x 1800mm
Corner brackets 90 x 35 x 240mm
Side top rails 148 x 48 x 800mm
Front/back top rails 90 x 35 x 1400mm
Coach bolts, nuts and washers 5/16 x 4 ½
Side bottom rails 90 x 35 x 800mm
Legs 98 x 98 x 900mm
Front/back bottom rails 90 x 35 x 1400mm
Shelf 800 x 1470 x 19mm
Bench stop 90 x 35 x 300mm
Tools
Claw hammer
Smoothing plane
Marking gauge
Combination square
Steel tape
Three beveled-edge firmer chisels
Cross-cut saw
Tenon saw
Nail punch
Twist drills
Screwdrivers
Oil stone
Sanding cork
Variable-speed power drill
Jigsaw
Circular saw
Instructions:
1. Cut to length the four legs and mark in housings for top and bottom rails. The top housing is 148mm x 48mm deep; the lower one 90mm x 35mm deep. Set your circular saw to the right depth and cut on the waste side of the lines you marked. Cut a series of parallel lines about 12mm apart between the housing marks and knock out waste. Smooth each housing with a chisel or rasp.
2. Cut to length front and back top and bottom rails, align them in their housing and pin in place with nails. Drill through both legs and rails as shown and bolt rails to legs. Check frame is square by measuring the diagonals.
3. Cut and clamp side rails to the front and back frame, then drill and insert the longer bolts. Tighten all nuts securely and check the table doesn't rock.
4. Cut out four corner brackets with 45-degree angles. A miter saw will be useful for this or set a circular saw to cut at 45 degrees. Screw brackets in place flush with top of rails. At this stage the bench frame should be completely rigid.
5. Cut the bottom shelf to suit the dimensions of the bench. Notch out 35mm x 133mm in each corner to clear the legs. The shelf can be screwed in place or left loose.
6. Cut the five pieces for the top. Move them around to get a good fit for the edges and hold them in place with a nail. Screw them to the bench frame with 100mm screws, two in each end, sunk slightly below the surface. Use a plane to smooth any major irregularities.
7. Prepare a bench stop as shown in the detail. Find the center and measure 60mm and 200mm from one end of a length of 90mm x 35mm pine. Drill an 8mm diameter hole at these points. Draw two lines joining the holes and cut along lines with a jigsaw to form a slot. Smooth the cut with a file or sharp chisel. Bevel the end at 45 degrees. Cut bench to a length of 300mm.
8. Locate the bench stop where you want it. Right-handed people generally prefer the stop at the left-hand end of the bench and left-handed people vice-versa. Make sure you avoid the braces. Hold the bench stop against the front rails and mark around it on the underside of the bench top. Transfer this shape to the top of the bench.
Drill two holes in opposite corners and cut out the rectangular hole. Insert the bench stop and make sure it slides smoothly. Adjust with a file or chisel as necessary. Hold the bench stop so it is flush with the bench top and drill a hole through the front rail at the top of the slot. Insert a carriage bolt with a washer and wing nut to allow the bench stop to be raised and lowered easily.
On the average, workbenches are not finished; i.e. do not apply paint or a clear finish so that this finish does not mark other items that are built on the bench.
For more information on benches visit http://www.bench411.com
About the Author
For more info & a free newsletter visit our blog at
http://myhomeimprovementtips.com
. More tips & resources on
benches
can be found at
http://www.bench411.com
 |
 Solid Wood Black Dining Table 5 Chairs Set Furniture with Bench NEW  US $2,899.99
|
 Amish Kitchen Nook Corner Table Set Storage Benches Solid Oak Wood Country New US $2,699.00
|
 Cherry Solid Hard Wood Rustic Dining Table 4 Chairs Bench Set for 6 People US $2,184.98
|
 Solid Wood Rustic Dining Table Chairs Set Furniture w Bench NEW US $2,184.98
|
 Rustic Trestle Square Table and Bench Set US $1,760.00
|
 HOMELEGANCE 586 AMEILLIA COLLECTION DINING TABLE SERVER BENCH 60 NEW SET US $1,626.00
|
 FREMONT 6pcs FORMAL COTTAGE RECTANGULAR DINING ROOM TABLE CHAIRS BENCH SET NEW US $1,495.73
|
 LIBERTY ASPEN SKIES CASUAL DINING SQUARE GATHERING TABLE BENCH SET COGNAC 6PC US $1,391.00
|
 NEW 6PC MARGAUX DARK CHERRY WOOD DINING TABLE SET BENCH US $1,306.25
|
 Solid Pine Wood Farm Table 1 Long Bench 4 Chairs WONDERFUL COUNTRY STYLE SET US $1,299.00
|
 6 Pc Oak 7Ft Table w 4 Side Chairs Bench Dining Set US $1,181.00 |
 8PC EXPEDITION BLACK WOOD SQUARE DINING TABLE SET BENCH US $1,139.05
|
 NEW 6PC KIRTLAND WARM OAK WOOD DINING TABLE SET BENCH US $1,139.05
|
 NEW 8PC BUTLER II ANTIQUE OAK WOOD COUNTER DINING TABLE SET CHAIRS BENCH US $1,139.05
|
 Amish Made Hand Crafted Solid Wood Dressing Table Vanity Bench Set New US $1,125.00
|
 LIBERTY AL FRESCO CASUAL DINING RECTANGULAR LEG TABLE SET WITH BENCH TAUPE 6PC US $1,094.00
|
 NEW 6PC NATICK BROWN CHERRY WOOD DINING TABLE SET BENCH US $1,091.55
|
 6PC DARK OAK FINISH WOOD DINING TABLE SET BENCH CHAIRS US $1,091.55
|
 NEW 6PC CLAYTON II CHERRY WOOD DINING TABLE SET BENCH US $1,091.55
|
 LIBERTY AL FRESCO II CASUAL DINING RECTANGULAR LEG TABLE SET BLACK 6 PIECE BENCH US $1,090.00
|
 EASTON 6pcs TRADITIONAL OAK RECTANGULAR DINING ROOM TABLE BENCH CHAIRS SET US $1,073.71
|
 New Wood Dining Set Table 4 Chairs Bench Dark Cherry Finish 60 78x 42 US $1,059.00
|
 NEW 6PC JUDSON CAPPUCCINO WOOD DINING TABLE SET BENCH US $1,044.05
|
 NEW 6PC EAGLEVILLE BROWN WOOD DINING TABLE SET W BENCH US $1,044.05
|
 NEW 8PC RUSTIC OAK COUNTER WOOD DINING TABLE SET BENCH US $1,044.05
|
 NEW 6PC BUTLER ANTIQUED OAK FINISH WOOD DINING TABLE SET CHAIRS BENCH US $1,021.25
|
Mike's reloading bench flexing solution.wmv